CFP Pleat-rite
Continuous Fiber Pleated Cartridges
Strainrite's Continuous Fiber Pleat (CFP) filter cartridges utilize a high surface area of small denier fibers to create more void volume in a highly uniform matrix, optimizing flow rate and service life without sacrificing particle efficiency. This revolutionary Micro-fiber optimizes pore size geometry required to offer absolute rated filtration performance. Our high efficiency media is non-calendared at the lower micron rating resulting in significantly reduced resistance to flow or pressure drop when compared to similarly rated polypropylene micro-fiber technologies.
The Continuous Fiber Pleat products are available in industrial grades that utilize epoxy binders or in FDA compliant grades, which utilize acrylic binders. Strainrite's CFP products are perfect for a wide range of applications where chemical compatibility is critical.
Typical Applications
- General Chemical
- Water filtration
- Solvent filtration
- RO/DI prefiltration
- Waste Water
- Oil and Gas Production
- Plating Solutions
- High efficiency media provides reliable, consistent and repeatable filtration results
- High surface area pleat design for greater surface area ensures longer service life, fewer changeouts and reduced operating costs per cartridge
- FDA Title 21 compliant for food and beverage contact
- Thermally bonded construction to ensure a cleaner filtrate
| Product Efficiency | ||
|---|---|---|
| CFP-Pleat-rite | 99.98% Efficiency | 90.00% Efficiency |
| CFP 0.25 | 0.8 μm | 0.25 μm |
| CFP 0.45 | 0.9 μm | 0.45 μm |
| CFP 0.65 | 1.0 μm | 0.65 μm |
| CFP 1.0 | 2.0 μm | 1.0 μm |
| CFP 1.5 | 3.0 μm | 1.5 μm |
| CFP 2.5 | 5.0 μm | 2.5 μm |
| CFP 5.0 | 10.0 μm | 5.0 μm |
| CFP 10.0 | 15.0 μm | 10.0 μm |
| Materials of Construction | |
|---|---|
| Filter Media: | Borosilicate Microfiberglass |
| Support Material: | Polyester |
| Hardware: | Polypropylene |
| Cage/Core: | Polypropylene |
| Sealing: | Thermal Bond |
| Seals: | Buna N, Fluorocarbon, EPDM FEP Encapsulated Fluorocarbon, PTFE, Silicone |
| Dimensions | |
| Outside Dia: | 2.55" (6.48cm) |
| Lengths: | 10" (25.4cm), 20" (50.8cm), 30" (76.2cm), 40" (102cm) |
| Performance Specification | |
| Retention Micron Rating: |
0.25, 0.45, 0.65, 1.0, 1.5, 2.5, 5.0, 10.0 |
| Maximum Forward Differential Pressure | |
| 75 psid @ 68°F (5.1 bar @ 20 C°) 40 psid @ 150°F (2.8 bar @ 65°C) |
|
| Maximum operating Temperature | |
| 180°F (82°C) Continuous Duty | |
| Toxicity | |
| All components meet all relevant USP XXII Class VI test for biological safety and FDA requirements for contact with food and beverage per 21CFR177.1520 | |
| Packaging Economy | |
| Bulk packaging in case quantities to reduce material disposal | |
| 10 inch | 24 per carton |
| 20 inch | 12 per carton |
| 30 inch | 12 per carton |
| 40 inch | 9 per carton |
| Cartridge Series | Micron Rating |
Length | End Cap Configurations | Gasket/O-Ring Materials | Cartridge Grade |
|---|---|---|---|---|---|
| ex. CFP Continuous Fiber-Pleat | 0.65 0.25 0.45 0.65 1.0 1.5 2.5 5.0 10.0 | -10 10 20 30 40 | C7 C1-Flat open ends C2-Recessed Cup/213 C3-Flat/222 C4-Flat closed ends C5-Recessed Cup/222 C6-Flat/226 C7-Fin/226 C8-Fin/222 | S S - Silicone (standard O-rings) B - Buna N (standard gaskets) V - Fluorocarbon E - EPDM T - PTFE TV - FEP Encapsulated Fluorocarbon |
Blank-General
1 - FDA Grade
Options I - 316 Stainless Steel Insert |
