Mem-PLEAT N
Nylon 6,6 Membrane Pleated Cartridges
Mem-PLEAT N pleated cartridges are highly retentive, naturally hydrophilic Nylon membrane filters that are specially designed for critical filtration requirements of aqueous fluids. The Nylon 6,6 membrane, in an all-polypropylene construction, provides excellent wet-out characteristics and superior flow performance per surface area as compared to other membrane cartridges. No additives, resins, surfactants or binders are used in the manufacturing process, which dramatically reduces rinse up time, extractables and downtime. Mem-PLEAT N cartridges are perfectly suited for critical applications where superior flow, and particle removal efficiency between 0.1 and 1.2 micron is required.
Typical Applications
- Reagent Grade Chemicals
- API Chemicals
- Fine Chemicals
- Biological Fluids
- Wine/Beverage Filtration
- 100% Hydrophilic materials of construction that are FDA listed as suitable for contact with food and beverage
- Absolute-rated media provides reliable, consistent and repeatable filtrate quality
- No adhesives, binders, resin or surfactants are used during manufacturing, resulting in superior downstream cleanliness
- High surface area, yielding lower pressure drops and longer filter life
- Lower filter extractables than other hydrophilic membranes
- Non fiber-shedding polyester and polypropylene support materials eliminate fiber migration
- IPA pre-wetting not required
- Manufactured in an ISO 9001 Certified Quality System Environment
- Integrity Testable
| Materials of Construction | |
|---|---|
| Membrane: | Nylon 6,6 cast on polyester |
| Support Material: | Polypropylene, Polyester |
| End Caps: | Polypropylene |
| Cage/Core: | Polypropylene |
| Sealing: | Thermal Bond |
| Seals: | Buna N, Fluorocarbon, EPDM FEP Encapsulated Fluorocarbon, PTFE, Silicone |
| Dimensions | |
| Outside Dia: | 2.55" (6.48cm) |
| Lengths: | 10" (25.4cm), 20" (50.8cm), 30" (76.2cm), 40" (102cm) |
| *Wine grade cartridges utilize FDA compliant polyester support material with stainless steel supported end caps | |
| Performance Specification | |
| Absolute Rated Retention: | 0.10, 0.20, 0.45, 0.65, 0.80, 1.20 |
| Maximum Differential Pressure | |
| Forward: | 75 psid @ 75°F (5.1 bar @ 75° C) 40 psid @ 180°F (2.8 bar @ 82°C) |
| Reverse: | 50psid @ 75° F (3.4 bar @ 24° C) |
| Maximum operating Temperature | |
| 180°F (82°C) Continuous Duty Polypropylene Hardware 275°F (135°C) Continuous Duty Polyester Hardware |
|
| Toxicity | |
| Cartridge materials meet CFR 21 for food and beverage contact | |
| Sterilization | |
| Cartridge can be sterilized via steam or Autoclave: 20 times at 275°F (135°C) Cartridge may be sanitized in place with common oxidizing agents, contact factory for chemical compatibility |
|
| Packaging Economy | |
| Bulk packaging in case quantities to reduce material disposal | |
| 10 inch | 24 per carton |
| 20 inch | 12 per carton |
| 30 inch | 12 per carton |
| 40 inch | 9 per carton |
| Cartridge Series | Micron Rating |
Length | Support Materials | End Cap Configurations | Gasket/O-Ring Materials | Cartridge Grade |
|---|---|---|---|---|---|---|
| ex. MPN Mem-Pleat N | 0.10 0.10 0.20 0.45 0.65 0.80 1.20 | -10 10 20 30 40 | PP PE - Polyester PP - Polypropylene | C7 C1-Flat open ends C2-Recessed Cup/213 C3-Flat/222 C4-Flat closed ends C5-Recessed Cup/222 C6-Flat/226 C7-Fin/226 C8-Fin/222 | S S - Silicone (standard O-rings) B - Buna N (standard gaskets) V - Fluorocarbon E - EPDM T - PTFE TV - FEP Encapsulated Fluorocarbon |
Blank-General
1 - FDA Grade
2 - Pharmaceutical
5 - Water
Options I - 316 Stainless Steel Insert DIF - DI Flush |
